Lab
Static Springs: Hooke's Law
Printer Friendly Version
Purpose
The purpose of this lab is to use linear regression and data analysis to calculate the elasticity constant for a single spring, and for springs arranged in series and in parallel.
Equipment
two springs
slotted masses
mass hanger
meter stick
support stand
Procedure and Data Tables
Part I: Single springs
. Complete ten trials for each spring. Initially record the equilibrium length of the spring without any suspended masses.
Then increase the hanging mass by increments of 100 grams and record each stretched length.
Continue until you have suspended a total of 1000 grams from each spring. Remember that the pan contributes 50 grams to each combination. Complete the following data table for each individual spring.
single spring #1
your group's spring
Equilibrium length
_____________
Trial
Total Hanging Mass
Total force (mg)
Final Length
Displacement
1
100 g
2
200 g
3
300 g
4
400 g
5
500 g
6
600 g
7
700 g
8
800 g
9
900 g
10
1000 g
single spring #2
your partnering group's spring
Equilibrium length
_____________
Trial
Total Hanging Mass
Total force (mg)
Final Length
Displacement
1
100 g
2
200 g
3
300 g
4
400 g
5
500 g
6
600 g
7
700 g
8
800 g
9
900 g
10
1000 g
Part II: Springs in Series
. Complete five trials using the springs from both groups. Arrange in series by linking them together one below the other. Initially record the equilibrium length of the springs without any suspended masses. Let your trials range from 100 grams to 500 grams.
springs in series
Equilibrium length
_____________
Trial
Total Hanging Mass
Total force (mg)
Final Length
Displacement
1
100 g
2
200 g
3
300 g
4
400 g
5
500 g
Part III: Springs in Parallel
. Complete five trials using the srping from both groups arranged side-by-side, or in parallel. Initially record the equilibrium length of the springs without any suspended masses. Let your trials range from 200 grams to 1000 grams. Be careful to make sure that the suspended masses are centered so that they are supported equally by both springs.
springs in parallel
Equilibrium length
_____________
Trial
Total Hanging Mass
Total force (mg)
Final Length
Displacement
1
200 g
2
400 g
3
600 g
4
800 g
5
1000 g
Data Analysis
EXCEL will now graph your data. Minimize your browser, double click My Computer, double click the shared drive and open the file called 1-
HookesLawAPC.xls
. You will most likely be asked to open the file as "read only" - that is fine. As soon as the file is open, use File Save As to rename the file as
LastnameLastnameHookesLaw.xls
on the shared drive. This copy of the file now belongs uniquely to your group. Remember that there are to be no spaces in the file name.
What is the name of your file?
Once you save your file with all of the information for each of the individual springs as well as the two special arrangements, go back and rescale any axes to insure that you maximize the display of your data. Then obtain a printout.
What is the numerical value of the slope of the individual graph of spring #1?
Write the equation of your group's graph using the correct experimental variables instead of EXCEL's generic x and y?
What is the numerical value of the slope of your partnering team's graph of spring #2?
Hooke's Law
When working with springs,
Hooke's Law
states that
F
distorting
= ks
where
F
distorting
is the applied force,
k
is the spring's elasticity constant measured in N/m, and
s
is the displacement, or how far the spring is stretched from its equilibrium position.
ALERT!
Note that in our lab our graphs have the applied force (the suspended weights) displayed on the x-axis and the spring displacements along the y-axis. This is because we manipulated the values of the suspended masses, resulting in force or weight being our independent variable while we merely recorded the stretched lengths as our experimental outcomes, or dependent values.
Consequently our graphs are titled
Displacement vs Force
and the elasticity constant for each of our spring systems will be calculated as the
reciprocal
of each graph's slope.
What is the elasticity constant for your group's original spring?
What is the elasticity constant for your partnering group's spring?
Springs in Series
We will now investigate the elasticity constant for springs arranged in series. The theoretical constant for such a system of springs is given by the formula:
What is the slope of your third graph when your springs were arranged in series?
Based on this slope, what is your experimental elasticity constant for when your springs were arranged in series?
Based on the formula, what is the theoretical value for the elasticity constant when your springs were arranged in series? (Show your calculations next to this graph.)
What is your percent error for this phase of the experiment? (Show your calculations next to this graph.)
How much energy was stored in the spring system when it supported 400 grams?
Springs in Parallel
We will now investigate the elasticity constant for springs arranged in parallel. The theoretical constant for a system of springs in parallel is given by the formula:
What is the slope of your fourth graph when your springs were arranged in parallel?
Based on this slope, what is the experimental elasticity constant for when your springs were arranged in parallel?
Based on the formula, what is the theoretical values for the elasticity constant when your springs were arranged in parallel? (Show your calculations next to this graph.)
What is your percent error for this phase of the experiment? (Show your calculations next to this graph.)
How much energy was stored in the spring system when it supported 400 grams?
Summary
When springs are connected in series, the spring constant of the system ____ when compared with the elasticity constant for either of the original springs:
increased
decreased
remained the same
When springs are connected in parallel, the spring constant of the system ____ when compared with the elasticity constant for either of the original springs:
increased
decreased
remained the same
Which arrangement of springs resulted in the greater amount of energy being stored in the system when syupporting 400 grams?
parallel
series
the same
After submitting your results online, turn in your written lab report to the one-way box. Each group should have a paper to support any and all numerical values that were submitted online as well as a printout of your graphs.
Related Documents
Lab:
Labs -
Coefficient of Friction
Labs -
Coefficient of Friction
Labs -
Coefficient of Kinetic Friction (pulley, incline, block)
Labs -
Conservation of Momentum in Two-Dimensions
Labs -
Falling Coffee Filters
Labs -
Force Table - Force Vectors in Equilibrium
Labs -
Inelastic Collision - Velocity of a Softball
Labs -
Inertial Mass
Labs -
LabPro: Newton's 2nd Law
Labs -
Loop-the-Loop
Labs -
Mass of a Rolling Cart
Labs -
Moment of Inertia of a Bicycle Wheel
Labs -
Relationship Between Tension in a String and Wave Speed
Labs -
Relationship Between Tension in a String and Wave Speed Along the String
Labs -
Static Equilibrium Lab
Labs -
Static Springs: Hooke's Law
Labs -
Static Springs: LabPro Data for Hooke's Law
Labs -
Terminal Velocity
Labs -
Video LAB: A Gravitron
Labs -
Video LAB: Ball Re-Bounding From a Wall
Labs -
Video Lab: Falling Coffee Filters
Resource Lesson:
RL -
Advanced Gravitational Forces
RL -
Air Resistance
RL -
Air Resistance: Terminal Velocity
RL -
Forces Acting at an Angle
RL -
Freebody Diagrams
RL -
Gravitational Energy Wells
RL -
Inclined Planes
RL -
Inertial vs Gravitational Mass
RL -
Newton's Laws of Motion
RL -
Non-constant Resistance Forces
RL -
Properties of Friction
RL -
Springs and Blocks
RL -
Springs: Hooke's Law
RL -
Static Equilibrium
RL -
Systems of Bodies
RL -
Tension Cases: Four Special Situations
RL -
The Law of Universal Gravitation
RL -
Universal Gravitation and Satellites
RL -
Universal Gravitation and Weight
RL -
What is Mass?
RL -
Work and Energy
Worksheet:
APP -
Big Fist
APP -
Family Reunion
APP -
The Antelope
APP -
The Box Seat
APP -
The Jogger
CP -
Action-Reaction #1
CP -
Action-Reaction #2
CP -
Equilibrium on an Inclined Plane
CP -
Falling and Air Resistance
CP -
Force and Acceleration
CP -
Force and Weight
CP -
Force Vectors and the Parallelogram Rule
CP -
Freebody Diagrams
CP -
Gravitational Interactions
CP -
Incline Places: Force Vector Resultants
CP -
Incline Planes - Force Vector Components
CP -
Inertia
CP -
Mobiles: Rotational Equilibrium
CP -
Net Force
CP -
Newton's Law of Motion: Friction
CP -
Static Equilibrium
CP -
Tensions and Equilibrium
NT -
Acceleration
NT -
Air Resistance #1
NT -
An Apple on a Table
NT -
Apex #1
NT -
Apex #2
NT -
Falling Rock
NT -
Falling Spheres
NT -
Friction
NT -
Frictionless Pulley
NT -
Gravitation #1
NT -
Head-on Collisions #1
NT -
Head-on Collisions #2
NT -
Ice Boat
NT -
Rotating Disk
NT -
Sailboats #1
NT -
Sailboats #2
NT -
Scale Reading
NT -
Settling
NT -
Skidding Distances
NT -
Spiral Tube
NT -
Tensile Strength
NT -
Terminal Velocity
NT -
Tug of War #1
NT -
Tug of War #2
NT -
Two-block Systems
WS -
Advanced Properties of Freely Falling Bodies #1
WS -
Advanced Properties of Freely Falling Bodies #2
WS -
Calculating Force Components
WS -
Charged Projectiles in Uniform Electric Fields
WS -
Combining Kinematics and Dynamics
WS -
Distinguishing 2nd and 3rd Law Forces
WS -
Force vs Displacement Graphs
WS -
Freebody Diagrams #1
WS -
Freebody Diagrams #2
WS -
Freebody Diagrams #3
WS -
Freebody Diagrams #4
WS -
Introduction to Springs
WS -
Kinematics Along With Work/Energy
WS -
Lab Discussion: Gravitational Field Strength and the Acceleration Due to Gravity
WS -
Lab Discussion: Inertial and Gravitational Mass
WS -
net F = ma
WS -
Practice: Vertical Circular Motion
WS -
Ropes and Pulleys in Static Equilibrium
WS -
Standard Model: Particles and Forces
WS -
Static Springs: The Basics
WS -
Vocabulary for Newton's Laws
WS -
Work and Energy Practice: Forces at Angles
TB -
Systems of Bodies (including pulleys)
TB -
Work, Power, Kinetic Energy
PhysicsLAB
Copyright © 1997-2024
Catharine H. Colwell
All rights reserved.
Application Programmer
Mark Acton